Screw jacks are mechanical actuators that convert rotary motion into linear motion. They are used for lifting, lowering, pushing, pulling, or positioning heavy loads. You’ll find them in machines, lifting platforms, automation systems, and many types of industrial equipment.

Selecting the right screw jack is important for safety, performance, and cost. The wrong choice may cause vibration, overloading, early wear, or even system failure. This guide will walk you through how to select the correct screw jack for your application.

We will cover:

  • What information you need before choosing a screw jack model
  • How to calculate working loads and speeds
  • How to choose the right screw jack type and size
  • What to check before confirming your selection

Whether you are a designer, engineer, or buyer, this guide will help you make the right choice.

Selection Parameters You Must Define

Before selecting a screw jack, you need to define several key parameters. These will directly affect the size, type, and configuration of the jack. Providing accurate data will ensure correct selection and long-term performance.

1. Load: How much weight does the jack need to lift or push? (in KN or Ton or KG) ?  Is it a constant load or does it change during operation?

2. Stroke: How far should the jack travel from start to end? (in mm)

3. Speed: How fast should the jack move? (mm/min or mm/sec)

4. Duty Cycle: How often will the jack operate? (cycles per hour/day)

5. Jack type you need : To choose the correct jack configuration, consider the following:

  • Will the jack be mounted upright or inverted?
  • Do you need a translating screw or a rotating screw with translating nut?
  • Is your installation vertical, horizontal, or mounted on a pivot?
  • For single jack systems, do you need a keyed screw to prevent unwanted rotation?  If you’re not sure what a keyed screw jack is, check this page for explanation.

If you’re not sure about these options, we recommend reviewing this guide for visual examples and explanations: Screw Jack Types – See Diagrams and Use Cases

6. Environment: Dusty, humid, high temperature, dusty?

7. Number of Jacks

  • Will you use a single jack or multiple jacks?
  • If multiple, will they move synchronously? Will handwheel or motors be used?

Not sure how multi-jack systems are connected?  Check typical configurations here: Screw Jack System Structures – View Examples

The Step-by-Step Selection Process (9 Steps)

Selecting the right screw jack doesn’t have to be complicated. This 9-step guide walks you through the entire selection process—from calculating load and verifying safety factors, to confirming RPM, torque, and model fit.

Whether you’re working with translating screw types or nut-rotating configurations, this process ensures your final selection is technically sound and ready for production. Follow each step to avoid costly mistakes and ensure long-term performance and reliability.

Start by calculating the adjusted load that each screw jack will handle. The actual working load must be increased using a safety factor to ensure stability under all conditions.

Formula:Ws = W × Sf

  • Ws = Adjusted load (KN or ton or KG)
  • W = Actual working load (KN or ton or KG)
  • Sf = Safety factor (based on application condition)

How to choose the safety factor:

Load ConditionTypical ApplicationsSuggested Coefficient
Smooth motion, no shockValve actuation, conveyor adjustment1.0 – 1.3
Light shock, medium loadGeneral transport lifters, automated feeding systems1.3 – 1.5
Severe shock or heavy vibrationLarge carriers, press rollers, high-impact industrial motion1.5 – 3.0

For high-frequency or outdoor use, always consider the upper end of the recommended range.

Example: If your actual load is 20 ton and your application is light shock, use Sf = 1.5:

Ws = 20 ton × 1.5 = 30 ton

This adjusted load will be used in the following calculations to size the jack properly.

Once the adjusted load (Ws) is known, the next step is to calculate how much load is applied to each jack. When using a synchronized drive system (such as a common shaft or gearbox), use a correction factor called the synchronous drive coefficient (fd) to account for uneven load distribution.

Formula: Load per jack = Ws ÷ (Number of jacks × fd)

Where:

  • Ws = Adjusted total load (N or Ton or KG or KN or LB)
  • fd = Synchronous drive coefficient (see table below)

Synchronous Drive Coefficient Table:

Example:
If the adjusted load is 10000 N and you’re using 4 jacks:   Load per jack = 10000 ÷ (4 × 0.85) = 2941 N

Choosing the correct screw jack type ensures your system operates reliably and efficiently. LiftingMotion provides four main types of screw jacks, each designed for specific performance needs and mechanical configurations.

To understand how these compare to standard industry classifications, see:  Exploring Screw Jack Varieties

Product Type Overview

For Harsh Environments

If the screw jack is used to push a vertical load (especially in long-stroke applications), you must check whether the screw shaft may buckle under compression. Buckling is a critical safety concern and can cause sudden failure.

When to Perform Buckling Check

  • Load is compressive (e.g., pushing upward)
  • Stroke is relatively long (typically >300 mm)
  • Jack is installed upright

Buckling Verification

Formula: PCR = m × (d / L)2

  • PCR = Allowable buckling load (N)
  • m = Support coefficient
  • d = Screw root diameter (mm)
  • L = Unsupported screw length (mm)

Support Coefficients

Installation ConditionSupport Coefficient (m)
A – Fixed base + shaft end free2.5 × 10⁴
B – Base + shaft end with clevis1.0 × 10⁴
C – Fixed base + guided shaft end + fixed shaft end2.0 × 10⁴

Select the condition that matches your mounting method.

screw buckling calculation

Safety Check Rule

 PCR ≥ W × SF
Where SF is the buckling safety factor (typically 4.0)
W = Load per jack (N)

Example (Based on Condition C)

  • Screw root diameter d = 38.42 mm
  • Screw projection distance L = 791 mm
  • m = 2.0 × 10⁴
  • W = 49000 N
  • SF = 4.0

PCR = 20×10⁴ × (38.42 / 791)2 = 695027 N
W × SF = 49000 × 4 = 196000 N
Result: 695027 N > 196000 N → Pass

If Buckling Risk Exists

  • Choose a larger jack size (with thicker screw)
  • Support the screw with a guide bushing
  • Select a configuration with higher support coefficient (e.g., Condition C)

When using a travel nut with screw shaft rotation, it’s essential to ensure the screw shaft rpm does not exceed the allowable limit.

If your input speed exceeds 900 r/min or you’re using high-speed stroke or a longer stroke, this check is required.

Formulas:

Screw Shaft RPM Verification

SymbolDescription
NCAllowable screw shaft rpm (r/min)
NSActual screw shaft rpm (r/min)
NInput rpm (r/min)
RWorm gear ratio
dScrew root diameter (mm)
nShaft end support coefficient: 0.36 (free end) / 1.56 (fixed end)
LSupport spacing distance (mm)
  • Allowable screw shaft rpm (NC):   NC = 96 × n × d × 10^6 / L²
  • Actual screw shaft rpm (NS):    NS = N / R
  • Ensure: NC ≥ NS

Example

Model: LMM20T screw jack
Input rpm: 1200 r/min
Gear ratio (R): 8
Shaft support: Fixed → n = 1.56
d = 51.3 mm, if L = 223.7 mm 

NS = 1200 / 8 = 150 r/min
NC = (96 × 1.56 × 51.3 × 10⁶) / 223.7² = 1535 r/min

Since NC > NS, it’s OK.

To select the right motor or drive, you need to calculate the required input RPM based on your desired lifting speed.

Formula: N = (V / ℓ) × R

  • N = Input RPM
  • V = Desired screw shaft speed (m/min)
  • ℓ = Screw lead (m)
  • R = Gear ratio

Example (Typical Use Case):

If you want the jack to move at 300 mm/min (i.e. 0.3 m/min),
and the screw lead is 6 mm (i.e. 0.006 m),
with a gear ratio of 24:1:

N = (0.3 / 0.006) × 24 = 50 × 24 = 1200 RPM

Note:
  • For screw jacks, input RPM should usually be ≤ 1750 RPM to ensure stable performance.
  • If the result is too high, consider using a jack with larger lead or lower gear ratio.

To select a suitable motor or manual drive, you need to calculate the required input torque (T) for the screw jack based on the lifting load and screw specifications.

Formula: T = (W × ℓ) / (2 × π × R × η) + T₀

  • T = Required input torque (N·m)
  • W = Lifting load (N)
  • ℓ = Screw lead (m)
  • R = Gear ratio
  • η = Efficiency
  • T₀ = Tare drag torque (N·m)

T₀ (tare drag torque) includes internal friction in the worm gear, screw nut, seals, and bearings.

  • For multi-jack setups, calculate total torque for each shaft line when sizing the motor.

After determining the required input torque and input speed, you must confirm whether the selected jack’s input shaft can handle the necessary power.

Formula:

P = (T × N) / 9550

Where:

  • P = Required input power (kW)
  • T = Required input torque (N·m)
  • N = Input speed (rpm)

How to Use:

  • Calculate the required power (P) using the formula above.
  • Compare the result with the maximum rated input power of the jack model.
  • If P exceeds the rated value, consider:
    • Increasing the jack frame size
    • Using a different gear ratio to reduce torque
    • Switching to a ball screw model for higher efficiency

Final Jack Model Confirmation:

Once speed, and power are verified within safe limits, you can confirm the selected screw jack model as suitable for your application.

Tip: LiftingMotion provide a max input capacity table in the technical page. Always verify against that reference.

Before placing your order, double-check the following key factors to ensure the jack you selected is safe and suitable for your application.

Pre-Selection Checklist:

  • Load Capacity: Make sure the jack can handle the adjusted load calculated in Step 1 and 2.
  • Screw Type: Choose between machine screw or ball screw, a worm gear or bevel gear—depending on your speed and duty cycle needs.
  • Buckling Check: If your application involves vertical compression and long strokes, ensure to verify the screw buckling.
  • Screw Shaft RPM Verification(for traveling nut type): If  input speed exceeds 900 r/min or or longer stroke, this check is required.
  • Input Power: Confirm the required motor power does not exceed the rated input capacity of the jack.
  • Working Conditions: For dusty, humid, or high-temperature use, check that the jack is configured with suitable materials and protection options.

Finalizing Your Model Code:

Once everything is confirmed, you can build your model code based on:

  • Jack Type (e.g., LMM, LML, LMB, LMLB)
  • Frame Size (e.g., 10, 25, 50)
  • Mounting (upright/inverted, screw translating/nut rotating, keyed or not)
  • Screw End (top plate, thread, clevis, etc.)
  • Stroke Length
  • Input Shaft Type (single shaft, double shaft, motor flange)
  • Motor Type (servo motor, stepper, single/three-phase, handwheel)
  • Optional Accessories (limit switch, boot, sensor, etc.)

Application: Four-jack synchronous lifting system powered by a 3-phase 220V/60Hz motor, used indoors in a low-dust environment. A guide mechanism prevents side loads. The system uses a fixed base with guided shaft ends on all jacks.

four screw jack systems

Usage Requirements:

  1. Load: 88.2 kN total / 4 jacks
  2. Speed: 10 mm/s (600 mm/min)
  3. Stroke: 300 mm
  4. Operation cycle: 2 times/hour × 8 hours/day × 300 days/year × 3 years

Calculation Steps:

  1. Adjusted Load:
    Using safety factor Sf = 1.3:
    Ws = 88,200 × 1.3 = 114,660 N

  2. Load per Jack:
    Using 4 jacks and fd = 0.85:
    W = 114,660 / (4 × 0.85) ≈ 33,724 N

  3. Preliminary Model Selection:
    Based on load, speed, and gear ratio, we choose
    LiftingMotion Model: LMB050-1A-6-300MM

  4. Buckling Check:
    Compression load requires buckling verification (Sf = 4):
    Pcr = 20 × 10^4 × (31.32 / 637)^2 = 473,073 N
    473,073 / 33,724 = 14 > 4 → OK

  5. Screw Shaft RPM Check:
    Not applicable here since this is not a travel nut type.

  6. Input RPM , Torque, Input capacity:

    • Input RPM: N = 600/0.010 = 360 r/min

    • Torque: T = (33,724 × 0.01)/(2 × π × 24 × 0.64) + 1.37 ≈ 15.4 N·m

    • Input Capacity: P = (15.4 × 360)/9550 = 0.58 kW
      Rated input of LMB050-1A-6-II-300MM-Q-C is 2.2 kW →OK

  7. Final Notes & Accessories:

  • Use the bellows to reduce dust–Q
  • Shaft End: top plate-II
  • Worm shaft: double shaft–C
  • Final model confirmed: LMB050-1A-6-II-300MM-Q-C

Need Help With The Screw Jack Selection?

Get Your Model in 10 Minute – For Free!

Our engineers use in-house software to select the exact model within 10 minutes. Just tell us your load, stroke, duty cycle, Jack configuration, and speed, and we’ll quickly provide:

  • Exact model recommendation

  • Free 2D & 3D CAD drawings

  • Layout suggestions to simplify installation

Fill out the form now, and let’s get your project moving!